Atlas Copco Authorized Sales and Service Distributor
Service & Maintenance 6 October 2026

What Is a Compressor Pressure Switch?

What Is a Compressor Pressure Switch?
The pressure switch, one of the most important control elements for the safe and efficient operation of compressed air systems, is an electromechanical device that continuously monitors air pressure in the system and regulates the motor accordingly. Acting as a kind of brain for the system, this part starts the compressor when the pressure in the air receiver drops to a preset lower limit and cuts the circuit to stop the motor when it reaches the upper limit.

In this process, which directly affects operating efficiency, a correct compressor pressure switch setting prevents the machine from being overloaded and avoids wasted energy. More than just a switching unit, this technology keeps system pressure within a set range to deliver the stable air the equipment on the production line needs, making it one of the cornerstones of industrial safety and operational continuity.

How Does a Compressor Pressure Switch Work?

The operating principle of a compressor pressure switch is based on the balance between the physical pressure force inside the air receiver and the resistance of a precision spring inside the switch mechanism. The system continuously senses air pressure through a diaphragm or piston connected directly to the receiver. As the amount of air in the receiver increases, the rising pressure pushes against this diaphragm. When the pressure reaches the upper limit preset on the switch (cut-out pressure), the diaphragm overcomes the spring's resistance, triggers mechanically and separates the electrical contacts. This cuts power to the motor and stops compression. When pressure drops as air is used, the spring's return force brings the diaphragm back to its original position, the contacts close again and the compressor starts up once more. This autonomous cycle keeps the system within safe limits without the need for constant supervision.

Why Is the Compressor Pressure Switch Setting Important?

In an industrial business, the compressor pressure switch setting plays an important role in keeping compressed air costs under control and protecting equipment life. Setting it correctly, above all, prevents the compressor motor from cycling on and off unnecessarily often, protecting the motor windings from heating and mechanical parts from premature wear. If the settings are wrong and the system is set to a higher pressure than necessary, every extra 1 bar of pressure increases energy costs by about 7%, which places a heavy burden on the operating budget in the long run.

In addition, a carefully made compressor pressure switch setting protects product quality by keeping the ideal pressure range needed by pneumatic equipment on the production line steady, and maximizes occupational safety by minimizing the risk of overpressure-related bursts or leaks across the system.

What to Watch Out for When Adjusting the Pressure Switch

Any work on the pressure switch directly affects both the mechanical health of the system and occupational safety. The most important thing before starting is therefore to make sure the unit's electrical supply is completely disconnected and the pressure in the receiver is at a safe level.

During adjustment, the maximum working pressure of the air receiver and other equipment in the system must never be exceeded, because a compressor pressure switch setting above the receiver's rated limit can lead to serious risks of explosion and equipment damage.

In addition, the difference between the lower pressure (cut-in) and the upper pressure (cut-out), that is, the differential, should not be kept too narrow. Too narrow a range makes the motor stop and start very often, shortening the life of the contactors and motor windings, while too wide a range can disrupt the stable air flow the machines on the production line need.

Steps to Adjust the Pressure Switch

When you move on to the adjustment, first remove the switch's protective cover to reach the adjustment screws. Most standard models have two main adjustment screws; the larger one usually controls the main spring tension, which moves both the lower and upper pressures up or down at the same time.

When adjusting the compressor pressure switch, turning the main screw clockwise increases the system's cut-out pressure. The second, usually smaller, screw sets the differential, that is, the pressure drop at which the compressor will start again. During adjustment, the compressor should be run and the values watched carefully on the pressure gauge. When the unit stops at the target upper pressure, some air should be released to check at what point it cuts in again, and fine adjustments completed with tiny turns based on these observations. At the end, make sure the screws are secured and confirm that the system completes at least two full cycles without problems before closing the cover.

Compressor Pressure Switch Faults and Solutions

Although pressure switches are durable components, because of their constantly moving mechanical parts and the electric current passing through them, they can show wear, oxidation or calibration drift over time.

One of the most common and most dangerous problems is the compressor not stopping even after reaching the set upper pressure. This is usually caused by the electrical contacts arcing and welding together, or by the compressor pressure switch being set to a point far above the unit's physical capacity. If the unit does not start at all, the switch's pressure inlet may be blocked or the diaphragm may have hardened and lost its sensitivity.

Another common fault is air leaking continuously from the relief valve under the switch after the compressor stops; although this is often confused with a check valve fault, it can also be caused by the trigger in the switch mechanism continuing to press on the valve. To solve such problems, the contact points should first be cleaned with fine sandpaper and the air inlet passages cleared of deposits, and if metal fatigue is observed in the spring mechanism, the switch should be replaced with a new one.

Don't Waste Energy with Incorrect Pressure Settings!

Your compressor running at a higher pressure than necessary means a hidden cost increase of 7% per bar on your electricity bills. Have your pressure switches calibrated with Yıldırım Soğutma's expertise to extend motor life and achieve maximum energy savings. Contact us to explore our professional solutions for all the compressor and chiller systems in your facility and to get a quote.

Frequently Asked Questions

How often should I adjust the pressure switch?

The pressure switch is usually set once, when the system is first installed or when the facility's air demand changes fundamentally. However, the setting can drift over time due to mechanical springs stretching, vibration and ambient conditions. During annual periodic maintenance, the pressure gauge readings and the switch's cut-in and cut-out points should therefore be checked, and if there is any deviation, a precise compressor pressure switch adjustment should be made again.

How can you tell if a compressor pressure switch has failed?

A fault usually shows itself through three main symptoms: the compressor not stopping even though it has reached the upper pressure limit, the motor not starting even though air pressure has dropped very low, or the motor stopping and starting at very short intervals. Continuous air leakage from the switch's relief valve after the motor stops, or a burning smell or arcing sound from the electrical contacts, are also clear signs that the switch has stopped working properly.

What are the consequences of setting the pressure switch incorrectly?

An incorrect compressor pressure switch setting has a chain of negative effects on the system. Setting the pressure too high strains the air receiver and piping, increases leaks and causes the motor to overheat. Setting the range between the lower and upper pressures (differential) too narrow makes the motor stop and start dozens of times an hour, burning out the contactors and causing energy costs to rise uncontrollably.

How does the pressure switch setting affect energy efficiency?

There is a direct correlation between energy efficiency and the pressure setting. According to industry standards, every unnecessary 1 bar increase in system pressure means about 7% extra cost in total electricity consumption. Running the system only at the minimum pressure needed, with a correct compressor pressure switch setting, prevents wasted energy and optimizes the compressor's loaded time, significantly reducing overall operating costs.