Atlas Copco Authorized Sales and Service Distributor
Service & Maintenance 6 October 2026

How Much Do Compressed Air Leaks Cost Your Business Each Year?

How Much Do Compressed Air Leaks Cost Your Business Each Year?
Even when compressed air leaks occur at small connection points, they can cause significant energy losses when they continue all year round. A healthy compressed air system requires leak flow to be measured, the annual cost to be calculated, leak points to be recorded and leaks to be fixed regularly. This keeps both energy consumption and system pressure under control. Air produced by the compressor escaping into the atmosphere before it reaches the point of use is one of the costs that directly increases a business's electricity consumption. The real cost of a leak depends on the hole size, system pressure, compressor efficiency, annual running hours and the electricity unit price. Compressed air leaks should therefore be seen not just as a technical maintenance issue but as a measurable energy loss.

Why Are Compressed Air Leaks Costly for Businesses?

Because compressed air is produced using electrical energy, any air that escapes into the atmosphere unused is a loss on which energy has already been spent. U.S. Department of Energy sources state that in poorly maintained industrial systems, leaks can reach around 20–30% of compressor output, and that effective leak detection and repair programs can bring this below 10%.

The cost of leaks is not limited to the electricity bill; longer compressor running times, pressure fluctuations and additional maintenance can also increase total operating costs.

How do leaks increase a compressor's energy consumption?

When there is a leak in a line, the compressor has to produce the lost air again even if actual production demand has not changed. As pressure starts to drop, the control system may keep the compressor loaded for longer or bring additional compressors online. This means the compressor also consumes electricity for air that is not used in production.

Raising the discharge pressure to compensate is not the right solution. Every 1 bar increase in system pressure can raise energy consumption by about 7%. Increasing the set pressure because of a leak in the compressed air system can therefore raise energy costs further instead of eliminating the loss.

How does pressure loss affect production performance?

Pneumatic hand tools, actuators, valves and production machines are designed to work at a specific inlet pressure. As leaks increase, the pressure at points of use can drop; equipment may run more slowly, cycle times may lengthen or process stability may suffer. This effect can become more pronounced at peak demand times, especially in facilities with many consumers on the same line.

When a pressure drop is seen, focusing only on increasing compressor capacity can therefore be misleading. The pressure in the compressor room should be compared with the pressure at critical points of use, and pipe diameters, filters, dryers and leaks should be examined together. This makes it possible to determine more accurately whether the problem comes from insufficient compressor capacity or from losses in the distribution network.

How Is the Annual Cost of a Compressed Air Leak Calculated?

To calculate the annual cost of a leak, the leak flow must first be determined. This flow is then assessed together with annual running time, the energy the compressor uses to produce a unit of air and the business's electricity unit price. The basic calculation can be done as leak flow × annual running hours × specific energy consumption × electricity unit price; the closer the measurement is to actual operating conditions, the more meaningful the cost calculation.

Leak volume, running time and electricity consumption

Leak flow can be measured in liters per second or cubic meters per hour. For example, a leak of 1.2 liters per second corresponds to 4.32 cubic meters of air per hour. For a facility that runs 6,000 hours a year, this means 25,920 cubic meters of lost air; the actual energy cost is found once the compressor's specific energy consumption and the current electricity tariff are added to the calculation.

For example, if the calculation assumes a specific energy consumption of 0.10 kWh/m³ and an electricity price of 5 TL/kWh, a leak of 4.32 m³/h creates an electricity cost of about 12,960 TL a year. This is only an example scenario prepared to show the calculation method; the real cost varies with the measured flow, working pressure, compressor efficiency, running hours and electricity tariff. A 1 mm leak at 7 bar is estimated to cause an air loss of about 1.2 l/s and an energy cost of several hundred euros a year.

Why can the annual cost of a small leak be higher than expected?

A low-flow leak at a connection may seem minor when observed briefly, but air keeps escaping for as long as the production line stays under pressure. A single leak can turn into thousands of hours of energy consumption in 24-hour production, on the night shift or when the system is not shut down at weekends. When there are dozens of similar points in the same facility, the total loss grows significantly.

The cost of a leak also rises as working pressure increases, because more air passes through the same opening. U.S. Department of Energy data show that at about 7 bar, an opening of 1/8 inch, or about 3.2 mm, can cost thousands of dollars a year in energy in a continuously running system. When assessing a compressed air system, you should therefore record not only large, easily noticed leaks but also small, continuous ones.

Where Do Compressed Air Leaks Occur Most Often?

Leaks can appear at different points in the system, but connections exposed to movement, vibration, frequent disconnection and aging seals carry a higher risk. Couplings, hoses, pipes, fittings, quick connectors, filter-regulator-lubricator units, condensate drains, valves and flanges are among the most common leak points. The check should therefore cover the entire distribution network, from the compressor outlet to the points of use.

Leaks in hoses, connections and fittings

Flexible hoses can be exposed to movement, abrasion, temperature changes and mechanical stress during operation. Over time, cracks can form on the hose surface or the end connections can loosen. Wear of the sealing elements in quick connectors due to frequent use also increases the likelihood of leaks.

Fittings and threaded connections can loosen due to improper installation, inadequate sealing or vibration. During the check, inspect not only the outer surface of the connection but also the inlet points of pneumatic equipment and the ends of lines that are no longer used. A line that is not used but left under pressure can consume air continuously without contributing to production.

Leaks in valves, filters, flanges and pipelines

Valve stem seals, body connections and internal mechanisms that do not close fully can develop leaks over time. Seal surfaces around filters and dryers, automatic condensate drains and flange connections are also areas that need checking. In particular, the sealing of parts that were removed and refitted during maintenance should be verified when the system is repressurized.

In pipelines, corrosion, mechanical damage, inadequate support or vibration can put stress on connection points. When an old compressed air system is extended, the points where new and existing pipe sections meet should be checked separately. Having an up-to-date line diagram of the system makes it easier to also inspect unused or overlooked sections during a leak survey.

How Is a Compressed Air Leak Detected?

Leak detection is not just about finding where the leak is; where possible, the leak flow or annual cost should be calculated and a follow-up measurement made after repair. Measuring total air consumption when production is stopped can give an idea of the system's overall leakage. In running facilities, methods such as listening, leak detection fluids and ultrasonic measurement can be used for different needs.

Detecting leaks by sound and pressure checks

Large leaks can be noticed by their hissing sound during quieter production hours. Applying a suitable leak detection fluid or soapy water to suspect connections helps confirm small connection leaks through bubble formation. This method is simple and low-cost, but checking an entire distribution network in a large facility can take time.

Pressure behavior is also an important indicator of leaks in the system. If the compressor frequently goes to load when there is no production, the flow meter shows flow when no air consumption is expected, or receiver pressure drops quickly, a leak is likely. However, when measuring, make sure that automatic drains or consumers that keep running do not affect the results.

Advantages of ultrasonic leak detection

  • Leaks can be checked while the system keeps running, so production does not need to be stopped.
  • By picking up high-frequency leak sounds the human ear cannot hear, it detects leaks that are hard to find by sight or by listening alone.
  • Because it can filter out audible production noise, it can be used effectively in noisy factories too.
  • By pointing toward the source of the sound, it helps pinpoint the location of the leak more precisely.
  • It makes it easier to check for leaks in high, narrow or physically hard-to-reach sections of pipelines.
  • It allows large compressed air networks to be surveyed faster than with methods such as soapy water.
  • It can be used to search for leaks in compressors, fittings, hoses, valves, flanges and various pneumatic equipment.
  • With suitable measuring equipment, the size of leaks can be estimated so the points causing the highest energy losses can be prioritized.
  • Leak points can be imaged, recorded and passed on to maintenance teams, making the repair process easier to track.
  • After repair, the same points can be checked again to confirm whether the leak has been fixed.
  • When used in regular surveys, it helps detect new leaks that appear later at an early stage.
  • By finding and fixing leaks, it helps reduce unnecessary compressed air production, energy consumption and the workload on the compressor.

What Should Be Done to Prevent Compressed Air Leaks?

Fixing leaks once does not mean the problem is gone for good; vibration, seal wear, hose movement and equipment changes can create new leaks over time. Leak management should therefore become a continuous maintenance program made up of regular surveys, recording, repair and verification. In addition, avoiding unnecessarily high pressure and isolating unused lines helps reduce the impact of new energy losses.

Regular leak checks and periodic maintenance

How often leaks are checked should depend on the size of the facility, its operating hours and the amount of equipment. Quarterly leak surveys can be a suitable starting interval for many businesses. In facilities with high vibration, older equipment or frequent connection changes, checks can be scheduled more often.

For each survey, the location of the points found, the leak size, the repair date and the result of the follow-up check should be recorded. Periodic maintenance of the compressor, dryer, filters and condensate drain equipment should also be carried out together with the leak program. This way, not only openings in the distribution network but also losses in the air production and treatment section can be checked regularly.

Running the compressed air system at the right pressure

The requirement of the equipment that needs the highest pressure in the business should be determined, and the compressor set pressure should be adjusted based on actual measurements at the points of use. Constantly raising compressor pressure to compensate for pressure losses caused by dirty filters or leaks is not energy-efficient. Every unnecessary 1 bar increase in pressure can raise the compressor's energy consumption by about 7%.

If some machines need higher pressure than others, the entire compressed air system does not have to run at that same high level. Depending on the application, local pressure boosting, a separate line or suitable regulation solutions can be considered. The aim is to supply each point of use with the pressure it needs without running the whole system at unnecessarily high pressure.

Improve the Efficiency of Your Compressed Air Systems with Yıldırım Soğutma

In addition to the sale, installation, periodic maintenance, technical service and genuine spare parts supply of Atlas Copco compressors, Yıldırım Soğutma helps choose the compressor that suits the business's air needs. Different requirements, from the operating conditions of the existing system to the capacity needed for new investments, are assessed to create solutions for reliable and efficient compressed air system operation.

Compressor maintenance and service

Yıldırım Soğutma provides periodic maintenance, technical service, installation and genuine spare parts support for Atlas Copco compressors. Maintenance is planned according to the compressor's running hours and service requirements, helping the system continue to meet production needs reliably.

Compressed air solutions for your business

Yıldırım Soğutma helps determine the right Atlas Copco compressor solutions by considering the air flow, pressure level, intensity of use and application conditions the business needs. With product options for different capacities and operating needs, it offers technical solutions for new investments as well as for improving existing compressed air systems.

Contact Yıldırım Soğutma to find the right compressor solution for your compressed air system and get detailed information.

FAQ

Do compressed air leaks increase the electricity bill?

Yes. Because the escaping air was compressed using electrical energy, the compressor may run longer or start more often to make up for the lost air. As the leak volume rises, so does the energy consumed without being used in production and the related electricity cost.

How much do compressed air leaks cost per year?

It is not right to give a single fixed amount. The annual cost depends on the leak flow, working pressure, annual running hours, the compressor's specific energy consumption and the electricity tariff. For example, a 1 mm leak at 7 bar can cause an air loss of about 1.2 l/s and an energy cost of around 300–400 euros a year.

How can you tell if there is a compressed air leak?

A hissing sound, air consumption that continues when there is no production, pressure dropping faster than expected and the compressor starting unnecessarily often can all be signs of a leak. Leak detection fluid can be used to confirm the location of small leaks, and an ultrasonic leak detector in large or noisy facilities.

Do compressed air leaks damage the compressor?

A leak does not always cause direct mechanical damage, but it can make the compressor run loaded for longer and go through more operating cycles. Besides energy consumption, this can increase the workload on the equipment and its maintenance needs.

How often should a compressed air leak test be carried out?

The check interval should be set according to the facility's conditions. Quarterly leak surveys can be a good starting program for many businesses; facilities with an old pipe network, heavy vibration or frequent equipment changes may need more frequent checks. An additional check after major maintenance, line changes or new equipment installation is also useful.

Does reducing compressed air leaks save energy?

Yes. Fixing leaks reduces the compressor's need to keep producing air that is not used in production. The amount saved depends on the current leak rate, running time and compressor control system, but fixing leaks directly improves energy efficiency, especially in a compressed air system with a high leak rate.